Відео

Can i use this with rnr motion 2.0 board?

Hi Franco , do you have an email ? , i have a question about your calibration , like if my motor does 1 rotation my lathe does 1.5 rotaton what would be the ration in my settings? And whats your signal debounce and PID and special spindle features ? , on my digital laser tach shows 1750 , the laith tach shoes 1750 and mach3 says measuring 500 rpm , sorry for so many questions but ive found very little info on calibration

Those Chinese reseller would make so much more money if they were not lazy and bothered to provide decent information with their products. You did a fantastic job. Thanks for making the files you found available. Much appreciated.

Great videos What’s the most reliable affordable way to Get a CMC machine for my shop To Mill Pistol slides for red dot Optics

How to remove a screw? My RC came with a bunch of screws loose, thread removed from facotry, so can't get them out. :D

How do you lift those suckers?

Which section did you download that shematic from?

Ok , this worked for me , I still need to adjust mach3 I think , couse after a bit it starts to rev up to high,

Can u tell me the differences between Closed Loop Stepper Motor series P , E and S ?? I don't understand the differences on the Stepper Online website . Thank's in advance !!

I’m new to setting up my nema 34 with the Acorn. What is the ideal step per rev do you recommend on the driver?

I'm trying to set up a spindle drive How do you set what output number for forward and reverse

What do you use your mills for?

1:53 I might be misunderstanding, but I think that the master tool method is really dumb on Centroids part. It may be friendly to beginners but generally what you should do is tram your spindle to the table or a height setter, again equipment that a beginner might not have, and then you set your tools based off of that. This method requires you to know what your longest tool is which is constantly changing especially for a beginner. Also I don't see the point when you might as well get the same result as your maximum tool size by just jogging your z-axis all the way up and saying that your master tool is in the spindle. I do understand why it would be good for hobbyists though with what you said about the home switches.

What a wonderful DOWN TO EARTH review!! Thank you very much Sir. Art from Ohio

Thanks

No wipers for the PM-25

How has it done for you over time? Just ordered two of these and a paraell kit to combine their power.

How do you make this bench lathe ridged enough for precision turning?

I need a calculation of DIY CNC machine's motor power. How can i calculate the powers? is here an anyone who knows that? pls help me

11:00 Why do you pulse the negative side? Most videos (and the guide from stepperonline) pulse positive side.13:50 ipm = inch per minute or is it 14:15 rpm? If it is the same in your case maybe you should describe why.

I still got mine. Runs really good still. I ran the ac in my camper off the 110 plug and I didn't have any issues.

Thats brilliant ❤ but i get an error whenever i try to export cnc file dump posts without any errors but export to cnc doesn't work and default extension for this export post is .nc not .cnc anybody can help me out with this?😢

But what does it say? “The word is near you, in your mouth and in your heart” (that is, the word of faith which we preach): 9 that if you confess with your mouth the Lord Yeshua ישוע (Jesus) and believe in your heart that God has raised Him from the dead, you will be saved. 10 For with the heart one believes unto righteousness, and with the mouth confession is made unto salvation. 11 For the Scripture says, “Whoever believes on Him will not be put to shame.” 12 For there is no distinction between Jew and Greek, for the same Lord over all is rich to all who call upon Him. 13 For “whoever calls on the name of the YHVH יהוה (LORD) shall be saved.” Romans 10:1-13

Did you possibly share you 3D gears on Thingiverse?

the sprocket are plastic? thank you

hello I would like to buy this tour. but I have a question please: the auto feed screw can it move in both directions of rotation? thank you

I have the screen up with VSC but it does not interact between the 2

Good video. I am a professional gunsmith/rifle builder and 1000yd competition benchrest shooter. A lot of friends of mine in the same business as me are running PM mills & lathes and are very happy. I hear customer service from Matt is the very best

i need the driver for xbox one controller

What size of material will either handle. Grizzly says its a 3" chuck. Is that the size if the chuck itself or will it handle 3" tubing?

This is a great idea, not only does it give you more Z clearance but you also get some extra extruded aluminum for making jigs or fences. We all know how much jigs and fences can be. Thank you, Franco. After 4 years I'm finally getting my machine together.

But what does it say? “The word is near you, in your mouth and in your heart” (that is, the word of faith which we preach): 9 that if you confess with your mouth the Lord Yeshua ישוע (Jesus) and believe in your heart that God has raised Him from the dead, you will be saved. 10 For with the heart one believes unto righteousness, and with the mouth confession is made unto salvation. 11 For the Scripture says, “Whoever believes on Him will not be put to shame.” 12 For there is no distinction between Jew and Greek, for the same Lord over all is rich to all who call upon Him. 13 For “whoever calls on the name of the YHVH יהוה (LORD) shall be saved.” Romans 10:1-13

Can encoder be fixed after over volatage ,driver flash 3ces after motor move and display red light. Test with another driver and it works but 2 driver affected can this be fixed .

Looking at getting this one. Costs alittle more now $479

The video title is wrong. Should be more like: Using a Grizzly Mill as punching bag to make the beloved PM Mill looking so, so, so much better. #sososososponsored

This is helpful.

HOLY RUSTY SHOCKS!!!! all joking aside thanks for the info!

Can u put c axis on mach4 or tail stock axis

Thank you SO much!!! How much were you selling these beauties for?

Ok so the wizard will not work without your "safe code" so its useless unless you can write g code

A rare view of comparison, side by side. this was great, I have been leaning towards the Precision Mathews anyway, but this helps. Grizzly seems a bit cruder.

How long did it take to receive it once you ordered it?

Thanks.

I know this is a 4 year old video, but any way you still have the 2d printed gear files? There in the link above.

Hey so I followed each step but when I go to print the nozzle drags on the plate. Do you think it's my z offset? If so what should it be at if my calibration was perfect?

I love the 3d printed gears idea. Any chance you could make and sell me a set?

I just bought a used mx-210v. the extra gears are missing. can I get a print on the gears you made? I can get a friend to print them for me. Im going to see if I can get this lathe to work for me before i resell it. thanks in advance.

Can you please give me the specs on the encoder you used?

Prior to connecting the driver to the computer and configuring it, were you able to move the motor at all? I get a red LED fault saying lost step after a small angle move of the shaft. sending pulses from an arduino. Gonna try to connect it to a uart cable like you did..